OpenICE Community Support Forum

Hey,

Having a look at your web demo, something seems off with your ventilator plots.

Hi to all the OpenIce team.

I am a french resident trying to implement an OpenIce server in our surgical intensive care in Paris.

I followed the setup provided in the documentation, and mine is as described :

- Philips IntelliVue MP70

- Ethernet cable

- RJ45 to DB9 modular adapter

- RS232 serial cape

- BBB

- TP-Link router

- Personal computer with OpenIce Supervisor

I have checked all the steps and I think the cabling is good (I'm using a male DB9 connector so the pin layout is reversed from your picture).

I'm nonetheless stuck at the "Requesting Association" step.

One thing I have not been able to do is to synchronize the date since I cannot access any NTP server from the hospital due to administrative restrictions.

I have a few questions :

- Does the clock icon signaling that my BBB is not synchronized with a NTP server (I tried to input a manual time through the date command, to no avail) can lock the association phase ?

- This is a RevG MP70, do I need to change the pin layout in the modular RJ45/DB9 cable ?

- I can't seem to find any way or any file to debug the messages that are sent through the /dev/ttyO1 serial device. Can you point me to a way to solve this issue ?

I want to thank you a lot for all the hard work and I'm looking forward to giving a little back if I can.

Regards,

JP

I am creating a new app like all other present in the openice.

I have created a package and also implemented the IceApplicationProvider interface but my app is not displayed on the main screen.

I am new to this can you guide me about how to solve this problem?

Hi,

I has try install OpenICE and successful installed.

I has create simulated device and link to patient (list in patient ID), it look working fine.

I has run HL7 export and start it, but HL7 message has been capture did not show active patient data , why this thing happened?

hope you can help me. thank you

Hi,

I am currently connecting Evita4 with laptop.

my connection is as follows:

evita->serial to usb connector ->laptop USB. I have crossed pin2 and 3(rx,tx) from evita.

Then i launch openice device configurator and add evita4 via serial. I tried all baudrates and parities. The device connector goes into endless connecting loop. However, I can use realterm to transmit basic commads and get replied.

Can you please provide steps to connect Evita 4.

Regards,

Tarun

Hello everybody,

I'm a newbie.I want to buy a BBB startkit to study openice.But I cant find a kit which can exactly meet the requirement mentioned in the article:a BBB kit with 'RS232 Cape'\'MircroSD Slot'\'Enclosure'.

Who can help me find an url to order the BBB kit which can directly deployed?

Hi MDPnP Team,

I noticed in your introduction video that you have a GE CareStation Ventilator in the lab. However, I don't see this ventilator as one of the supported devices in OpenICE. Do you have any plans to include GE CareStation as one of the supported devices anytime soon?

Thanks.

Hi

Firstly, thanks to the OpenICE community for supporting this amazing project.

I'm trying to use OpenICE (v0.6.3) to connect to Philips IntelliVue monitors over LAN. My computer (OSX 10.11.3) is connected to the same internal ICU LAN network the monitors are connected to. I have an IP address, and I can ping the monitors. However, when I connect to the monitor IP address, the connection status in OpenICE is stuck on "Negotiating (Requesting association)". This is true of any monitor I attempt to connect to in the unit. Just to be explicitly clear, I am not using serial/RJ45/RS232. Just LAN.

I am able to connect to the monitor just fine when the monitor is connected to an isolated network. I believe the issue may be that the monitors are already connected with the central Philips server. Can IntelliVue monitors connect to both the Philips server and OpenICE simultaneously? Is there any other reason that could explain this behaviour?

Kind regards

Luke Fletcher

Hi guys,

I am Happy and excited to find OpenICE, and this forum.

I am planning to connect IntelliVue MX800 with OpenICE. So from Docs, i can understand that, no need of BBB for simple connection. Just connect RS232 port on MX800 to OpenICE (via RJ45 -> DB9 -> USB). I can see 2 RS232 port in the MX800.

Which port i should use for serial communication?

Another question is, can i direct connect MX800 to openICE using LAN cable (By connecting the LAN port in MX800 and Ethernet port in Laptop )?